English- English
-
Español -
Português -
русский -
Français -
日本語 -
Deutsch -
tiếng Việt -
Italiano -
Nederlands -
ภาษาไทย -
Polski -
한국어 -
Svenska -
magyar -
Malay -
বাংলা ভাষার -
Dansk -
Suomi -
हिन्दी -
Pilipino -
Türkçe -
Gaeilge -
العربية -
Indonesia -
Norsk -
تمل -
český -
ελληνικά -
український -
Javanese -
فارسی -
தமிழ் -
తెలుగు -
नेपाली -
Burmese -
български -
ລາວ -
Latine -
Қазақша -
Euskal -
Azərbaycan -
Slovenský jazyk -
Македонски -
Lietuvos -
Eesti Keel -
Română -
Slovenski -
मराठी -
Srpski језик
Introduction of Road Stud
2021-08-26
Road studs, a commonly used method of traffic roadblocks, are used to guide people to drive in the right direction and prevent speeding and traffic accidents. Mainly used in roads and railways.
Basic Information:
The specifications of road studs are generally 100mm*100mm*20mm, and the maximum height does not exceed 25mm. There are many kinds of reflectors, including reflectors, reflectors, LEDs, reflective films, etc.
The installation of road studs generally adopts epoxy resin installation.
There are many classifications of road studs, which can be divided into:
1. Cast aluminum road stud;
2. Plastic road studs;
3. Ceramic road studs;
4. Glass fairway spikes;
5. Reflective bead road studs (21 beads and 43 beads, which can be combined into cast aluminum and plastic road studs)
6. Mine spikes;
According to the function, it can be divided into:
1. Ordinary spikes;
2. Solar road studs,
3. Cable spikes in tunnels;
4. Wireless road studs.
According to the number of reflective surfaces, it can be divided into:
Single-sided road studs and double-sided road studs.
installation method:
1. The placement and installation of safety isolation facilities is a very important point. I hope that everyone must not ignore it. In the entire dynamic construction process, whether it is a new road or an open road, everyone should be in the safety facility. If the construction is on a traffic road, the ratio of safety personnel to installation personnel should be 1:1. For construction on unopened sections, the ratio of safety personnel to installation personnel should be 1:3.
2. Determine the installation location and ensure that the installation location is level. For roads with expansion, cracks, and unevenness, the roads should be smoothed and leveled in advance.
3. Clean the installation location with a brush and make sure that the installation location is dry.
4. Take an appropriate amount of glue and apply it evenly on the spikes.
5. Tightly press the spike on the installation position, make sure the direction is correct, if there is too much glue, be sure to clean it up;
6. If it is a cast aluminum spike with feet, make sure that the depth of the hole is greater than the depth of the nail foot by 1cm, and the diameter of the hole is greater than the diameter of the nail foot by 2mm.
7. Do a tour within two hours after the spikes are installed to make sure that all spikes are not reversed, crooked or crooked.
8. After the road studs are cured for 4 hours, remove and install the isolation facilities.
Basic Information:
The specifications of road studs are generally 100mm*100mm*20mm, and the maximum height does not exceed 25mm. There are many kinds of reflectors, including reflectors, reflectors, LEDs, reflective films, etc.
The installation of road studs generally adopts epoxy resin installation.
There are many classifications of road studs, which can be divided into:
1. Cast aluminum road stud;
2. Plastic road studs;
3. Ceramic road studs;
4. Glass fairway spikes;
5. Reflective bead road studs (21 beads and 43 beads, which can be combined into cast aluminum and plastic road studs)
6. Mine spikes;
According to the function, it can be divided into:
1. Ordinary spikes;
2. Solar road studs,
3. Cable spikes in tunnels;
4. Wireless road studs.
According to the number of reflective surfaces, it can be divided into:
Single-sided road studs and double-sided road studs.
installation method:
1. The placement and installation of safety isolation facilities is a very important point. I hope that everyone must not ignore it. In the entire dynamic construction process, whether it is a new road or an open road, everyone should be in the safety facility. If the construction is on a traffic road, the ratio of safety personnel to installation personnel should be 1:1. For construction on unopened sections, the ratio of safety personnel to installation personnel should be 1:3.
2. Determine the installation location and ensure that the installation location is level. For roads with expansion, cracks, and unevenness, the roads should be smoothed and leveled in advance.
3. Clean the installation location with a brush and make sure that the installation location is dry.
4. Take an appropriate amount of glue and apply it evenly on the spikes.
5. Tightly press the spike on the installation position, make sure the direction is correct, if there is too much glue, be sure to clean it up;
6. If it is a cast aluminum spike with feet, make sure that the depth of the hole is greater than the depth of the nail foot by 1cm, and the diameter of the hole is greater than the diameter of the nail foot by 2mm.
7. Do a tour within two hours after the spikes are installed to make sure that all spikes are not reversed, crooked or crooked.
8. After the road studs are cured for 4 hours, remove and install the isolation facilities.
Road stud installation is not a complicated matter, but there are many details that need attention. These details play a very important role in ensuring the quality requirements and service life of road studs.
Previous:Introduction to Traffic Cones
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies.
Privacy Policy